PERPUSTAKAAN BIG

  • Beranda
  • Informasi
  • Berita
  • Bantuan
  • Area Pustakawan
  • Area Anggota
  • Pilih Bahasa :
    Bahasa Arab Bahasa Bengal Bahasa Brazil Portugis Bahasa Inggris Bahasa Spanyol Bahasa Jerman Bahasa Indonesia Bahasa Jepang Bahasa Melayu Bahasa Persia Bahasa Rusia Bahasa Thailand Bahasa Turki Bahasa Urdu
Image of Estimating uncertainties in 3-D models of complex fold-and-thrust belts: A case study of the Eastern Alps triangle zone

Text

Estimating uncertainties in 3-D models of complex fold-and-thrust belts: A case study of the Eastern Alps triangle zone

Sofia Brisson - Nama Orang; Florian Wellmann - Nama Orang; Nils Chudalla - Nama Orang; Jan von Harten - Nama Orang; Christoph von Hagke - Nama Orang;

Geological modeling commonly results in a single prescribed geometric representation of the subsurface with no consideration of uncertainties. Accounting for uncertainties is of particular importance in the triangle zone at the leading edge of deformation of the foreland fold-thrust belt of the European Alps, the Subalpine Molasse. Here, interpretations of the complex structures are limited to 2D and are based almost exclusively on subsurface data, lacking the constraint of surface data.
Implicit modeling can be used to create automated 3D model realizations considering parameter uncertainty. In this sense, multiple possible models can be assessed within the uncertainty range assigned. As implicit modeling often yields artifacts or geologically unfeasible scenarios, the concept of geological topology can be used to constrain the modeling outputs, so that only models without artifacts are considered into the final model ensemble.
Two experiments are designed to test out this workflow. The methodology is first tested using a very simple synthetic model, and later applied to a portion of the Subalpine Molasse, where different 2-D subsurface geometries have been proposed. For the first time, a 3D implicit model ensemble incorporating a full assessment of uncertainties is built in this area. Results show that it is feasible to use topological information for posterior model constraint, even in models of high structural complexity. To eliminate all non-meaningful models, however, it is necessary to use more than one topological constraint. A comparison of the prior and posterior model ensembles shows a correlation between model parameters and a shift in parameter probability density curves in the synthetic model experiment, and a decrease in entropy for both experiments. A topological constraint should thus be applied routinely when building a stochastic implicit model ensemble.


Ketersediaan
147551.136Perpustakaan BIG (Eksternal Harddisk)Tersedia
Informasi Detail
Judul Seri
Applied Computing and Geoscience - Open Access
No. Panggil
551.136
Penerbit
Amsterdam : Elsevier., 2023
Deskripsi Fisik
16 hlm PDF, 11.035 KB
Bahasa
Inggris
ISBN/ISSN
2590-1974
Klasifikasi
551.136
Tipe Isi
text
Tipe Media
-
Tipe Pembawa
-
Edisi
Vol.18 June 2023
Subjek
3D implicit modeling
Uncertainty topology
Eastern Alps
Triangle zone
Info Detail Spesifik
-
Pernyataan Tanggungjawab
-
Versi lain/terkait

Tidak tersedia versi lain

Lampiran Berkas
  • Estimating uncertainties in 3-D models of complex fold-and-thrust belts: A case study of the Eastern Alps triangle zone
    Geological modeling commonly results in a single prescribed geometric representation of the subsurface with no consideration of uncertainties. Accounting for uncertainties is of particular importance in the triangle zone at the leading edge of deformation of the foreland fold-thrust belt of the European Alps, the Subalpine Molasse. Here, interpretations of the complex structures are limited to 2D and are based almost exclusively on subsurface data, lacking the constraint of surface data. Implicit modeling can be used to create automated 3D model realizations considering parameter uncertainty. In this sense, multiple possible models can be assessed within the uncertainty range assigned. As implicit modeling often yields artifacts or geologically unfeasible scenarios, the concept of geological topology can be used to constrain the modeling outputs, so that only models without artifacts are considered into the final model ensemble. Two experiments are designed to test out this workflow. The methodology is first tested using a very simple synthetic model, and later applied to a portion of the Subalpine Molasse, where different 2-D subsurface geometries have been proposed. For the first time, a 3D implicit model ensemble incorporating a full assessment of uncertainties is built in this area. Results show that it is feasible to use topological information for posterior model constraint, even in models of high structural complexity. To eliminate all non-meaningful models, however, it is necessary to use more than one topological constraint. A comparison of the prior and posterior model ensembles shows a correlation between model parameters and a shift in parameter probability density curves in the synthetic model experiment, and a decrease in entropy for both experiments. A topological constraint should thus be applied routinely when building a stochastic implicit model ensemble.
Komentar

Anda harus masuk sebelum memberikan komentar

PERPUSTAKAAN BIG
  • Informasi
  • Layanan
  • Pustakawan
  • Area Anggota

Tentang Kami

Perpustakaan Badan Informasi Geospasial (BIG) adalah sebuah perpustakaan yang berada di bawah Badan Informasi Geospasial Indonesia. Perpustakaan ini memiliki koleksi yang berkaitan dengan informasi geospasial, termasuk peta, data geospasial, dan literatur terkait. Selengkapnya

Cari

masukkan satu atau lebih kata kunci dari judul, pengarang, atau subjek

Donasi untuk SLiMS Kontribusi untuk SLiMS?

© 2025 — Senayan Developer Community

Ditenagai oleh SLiMS
Pilih subjek yang menarik bagi Anda
  • Batas Wilayah
  • Ekologi
  • Fotogrametri
  • Geografi
  • Geologi
  • GIS
  • Ilmu Tanah
  • Kartografi
  • Manajemen Bencana
  • Oceanografi
  • Penginderaan Jauh
  • Peta
Icons made by Freepik from www.flaticon.com
Pencarian Spesifik